Dish Remote Not Working – Easiest Solutions

We all have faced this situation in our life where we get stuck with our dish remote not working, and no doubt this is a very irritating situation to be in. If you are here, then I assume you are facing this problem as well but worry not because we are going to discuss this problem and try to give simple and easy DIY solutions on how to fix dish remote not working. There could be several reasons you are facing this problem, but we will try to cover every possible solution, so just stick with us and keep scrolling to fix this.

My Dish remote not working? 5 ways to fix

Usually, when a dish remote stop working or become unresponsive, there is the possibility that this remote stops working on your particular Dish device. Still, the first response of Dish users is to abandon their old remote and get a new one and not even consider that the old remote may have some minor technical problem that can be easily fixed in most cases.

Try New Batteries

Low remote batteries are the most common problem of the dish remote, so to troubleshoot that our remote is okay, just try to replace the batteries and see if it works.

Try your dish remote on Another Device

If the previous solution didn’t work and your dish remote is not working with no lights even after installing the new batteries, then try your remote on another device to eliminate the possibility of a broken receiver.

You can ask a friend to check your remote on their dish. If the remote is not working on their dish, then move on to the next solution on our list.

dish remote not working even with new batteries

Now that we know that our batteries are working fine and the dish remote is not working after changing the batteries, we will try to rest our Dish remote. Just follow the following easy and simple steps to reset your Dish remote.

Re-programme You Dish Remote

We will try to program our Dish remote. There are two ways we can use to program our Dish remote, but it depends on the model of the dish we are using. The programming process we are going to explain will work on models 40.0, 50.0, 52.0, and 54.0, so if you have purchased your dish in the last few years, then it should work for you, but if your dish is very old then this process might not work for you but be sure to give it a try. Here is the step-by-step guide to reprogramming your dish remote.

1. Press the “Home button” on your remote twice, or it can be the” Menu” button if you use an old dish remote.
2. Go to the settings from the menu.
3. Now select “Remote Control.”
4. from there.
5. Now choose the device you are looking to pair.
6. Find and select the pairing Wizard from the menu. It will ease the process even more.
7. Now we need to find the other devices we are pairing with.
8. Select our device.
9. Now the pairing Wizard will ask you to try some codes. Just follow the on-screen instruction to test the codes.
10. Now the pairing process will start.
11. You should test your Dish remote even if the Pairing process worked perfectly.

dish remote not working with receiver? Restart It

It is possible that even after the reprogramming of the remote, your dish remote is still not working. In that case, we need to do this last thing, and our remote will be fine in this solution, we will restart our Dish receiver and the TV. Just follow these steps.

1. Press and Hold the “Reset” button
2. It can be the “Power” button for you
3. When your receiver restart.
4. Now restart your TV as well.

dish remote wont turn off tv? Fix now

Frustrated with your Dish remote’s inability to turn off your TV? We’ve all been there—sitting on the couch, reaching for the remote, pressing the power button repeatedly, only to find that the TV remains stubbornly on. But fear not! We’ll explore the common issue of a Dish remote not turning off the TV and provide you with practical solutions to get your remote back in control. From checking the batteries to re-pairing the remote, we’ve got you covered.

Check the Remote Batteries

• Open the battery compartment on the back of your Dish remote.
• Remove the batteries and inspect them for any signs of corrosion or damage.
• If the batteries are old or depleted, replace them with fresh batteries.
• Make sure the batteries are inserted correctly, matching the positive (+) and negative (-) signs.
• Test the remote to see if it can now turn off the TV. If not, proceed to the next solution.

Re-Pair the Remote with the TV

• Locate the remote control programming codes for your TV model. You can find these codes in the Dish remote control manual or on the Dish website.
• Press and hold the TV mode button on your Dish remote until all the mode buttons light up.
• Enter the programming code for your TV using the number buttons on the remote.
• Press the Pound (#) button. The TV mode button should flash three times.
• Test the remote by pressing the power button to turn off the TV. If the issue persists, try programming the remote with a different code for your TV model.

Conclusion for dish remote stopped working

So these were five simple and easy fixes you can use to fix your dish remote not working error quickly. If your remote is still not working, make sure there is nothing between your remote and receiver to stop the connection, and if you have finally decided to buy a new remote, then we suggest you buy a universal remote.

---

FAQs

How come my DirecTV remote won’t work?

There could be several reasons why your DirecTV is not working. Just remove any object that could be blocking the connection and try to replace the batteries.

Can I use my phone as a dish remote?

You can use the DISH anyway app to get the live TV on your smartphone and connect your phone to your dish TV using Bluetooth.

How do I reset my dish network remote control?

Press the “Sat” on the remote, followed by the “Sys info/System info” button on the front of the receiver. From there, just activate the Wizard and follow the instruction.

Is there a reset button on a DISH remote?

No, there is no rest button on the remote.

How do you work a dish remote?

First, try to identify the problem. Mostly the batteries of the remote are dead change the batteries on the dish remote, and it should work fine.

How do you pair a remote to a Joey?

Follow these steps to pair a remote with joey:

Press the HOME button two times.

Go to Settings.

Select Remote Control.

Select the device code.

Open the Pairing Wizard for your device.

Now follow the on-screen instruction.

How do I program my Dish Network remote without a code?

you can program Dish remotes without knowing the code. Just use the Pairing Wizard from the Settings menu.

Why does my DISH remote not control the volume?

You can fix the dish remote volume buttons by restarting the receiver. Then you will need to reprogram the remote to your TV again and check if it is set to control the TV’s volume.

How do I connect my Dish remote to my TV?

Go to the receiver menu => settings= > remote control => pairing wizard => select your device brand => press volume Up to test the code => if the code works => fisnish.

How do I reboot my Dish TV?

First, Unplug the power cord of your dish from the outlet for 10 seconds, then plug it back in and restart your TV.

How do you pair a remote to the hopper?

Press the “Sys info” => Sat button on the remote, and that’s it. Your remote should now get paired with the hopper.

Is DISH Network remote universal?

Yes, you can use the dist remote as the universal remote.

Is there a universal remote that works with Dish Network?

Yes, there are a lot of universal remotes that can work with the Dish network perfectly fine.